PETG
PETG
PETG is a tough, low-warp filament that handles more heat and moisture than PLA and prints without an enclosure, at the cost of stringing and fussier bed adhesion.
What it is
PETG (polyethylene terephthalate glycol-modified) is the most common step up from PLA for functional parts. Prusa's knowledge base describes it as easy to print, tough and durable, with good layer adhesion, low warping, higher temperature resistance and resistance to water and humidity. Prusa says PETG parts suit interior and most exterior use at temperatures below 80 °C.
Bambu Lab describes its PETG HF as keeping the strengths of regular PETG, including resistance to water, UV and temperature, and suggests it for items such as planter pots, watering cans and automotive parts. Because it warps much less than ABS, it still prints well on open-frame printers.
Print settings in practice
PETG runs hotter than PLA, and makers' windows vary more:
- Bambu filament guide (PETG): 240 to 270 °C nozzle, 60 to 80 °C bed on its Engineering, High Temperature and Textured PEI plates.
- Bambu PETG HF: 230 to 260 °C nozzle, 65 to 75 °C bed with glue, under 300 mm/s.
- Polymaker PolyLite PETG: 230 to 240 °C nozzle, 70 to 80 °C bed, cooling fan off to 20%, 30 to 50 mm/s.
- Prusa: 230 °C first layer and 240 °C after, with an 85 °C first layer bed and 90 °C after.
The 240 °C nozzle and 75 °C bed in the settings table sit inside the Bambu and Polymaker ranges. Prusa's recommended bed is higher, so if you print on a Prusa sheet, follow Prusa's numbers.
Bed surface matters more than with PLA. Prusa warns: "Do not print on the smooth PEI sheet as the adhesion may be too strong!" It recommends a textured or satin sheet, or a layer of glue stick if you must use smooth PEI. Bambu also lists glue for PETG HF. Prusa's advice is to use glue on smooth PEI because adhesion there can be too strong and may damage the sheet.
Stringing is the classic PETG complaint. Prusa suggests more retraction, a lower nozzle temperature and print cooling to reduce it.
An enclosure is not required, and standard nozzles are fine for unfilled PETG. Carbon-filled grades are abrasive and need a hardened nozzle (see PETG-CF).
Strengths and weaknesses for real projects
PETG suits brackets, mounts, enclosures, outdoor fittings, planters and parts that live in a warm room or a car interior that never gets extremely hot. Its heat figures are a clear step above PLA: Polymaker lists a heat deflection temperature of 74.8 °C at 1.8 MPa and a Vicat softening temperature of 84 °C for PolyLite PETG, and Bambu lists 69 °C (0.45 MPa) and 70 °C Vicat for PETG HF.
The weaknesses are mostly about print quality. Prusa lists stringing, poor bridging and overhangs, less suitability for very detailed parts, strong bonding to the print surface, hard-to-remove supports and solubility in dangerous chemicals. For crisp miniatures or sharp display pieces, PLA is usually the better pick.
How it compares
- PLA and PLA+: easier and crisper, but soften around 55 to 60 °C. PETG trades some detail for roughly 10 to 20 °C more heat headroom, depending on which published figures you compare (for example 57 vs 69 °C at 0.45 MPa for Bambu PLA Basic and PETG HF, 54 vs 74.8 °C at 1.8 MPa for Bambu PLA Basic and Polymaker PETG).
- ABS: more heat resistant (Polymaker lists 98.2 °C heat deflection for PolyLite ABS) and can be acetone smoothed, but warps and needs an enclosure and ventilation.
- ASA: the choice for long outdoor exposure plus heat, with Prusa calling out its high UV resistance. It also needs an enclosure.
- TPU: when the part must flex like rubber.
Which printers on this site can print it
PETG prints well on open-frame and enclosed printers alike. Check that the bed reaches the temperature your filament asks for: the Bambu Lab A1 mini tops out at 80 °C, which covers the Bambu and Polymaker ranges but not Prusa's 90 °C. At the time of writing (October 2026), official store prices included:
- Creality Ender-3 V3 SE at $179; Creality says its Sprite extruder works with PLA, PETG and TPU.
- Bambu Lab A1 mini at $199, with an 80 °C bed.
- Flashforge Adventurer 5M at $249, where Flashforge recommends PLA and PETG with the 0.4 mm nozzle.
- Bambu Lab A1 at $259, with a 100 °C bed.
- Bambu Lab P1S at $349, enclosed, with Bambu listing PETG as an ideal material.
- Bambu Lab X2D at $589, which Bambu says is UL 2904 certified for indoor air quality with its PLA Basic and PETG Basic.
See also our best budget 3D printers and best 3D printers for home use.
Safety and food contact
UL Research Institutes reports that material extrusion printing emits ultrafine particles and volatile organic compounds that vary by filament and print conditions, so ventilating the room is a sensible default.
On food contact, Prusa says "PETG in itself may be considered" food-safe, but layer lines can let bacteria grow over time, and it does not recommend PETG or any other filament for dishes or items in direct food contact. If you still want to, Prusa suggests a food-safe epoxy coating and a stainless steel nozzle. Bambu's PETG HF page makes no food-contact claim, so do not assume a given spool qualifies.
Storage
PETG is more sensitive to moisture than PLA. Bambu says PETG HF "must be dried before use and remain moisture-free during the printing process, especially for longer print times (over 6 hours)." It recommends drying at 65 °C for 8 hours (or 75 to 85 °C for 12 hours on an X1-series heatbed) and storing below 20% relative humidity, sealed with desiccant. Polymaker recommends printing from a dry box and storing spools in their resealable bag.
Print settings
| Type | PETG |
|---|---|
| Brand | Various |
| Nozzle / print temp | 240 °C |
| Bed temp | 75 °C |
| Price | Not listed |
Pros and cons
Pros
- Higher heat resistance than PLA (HDT about 69 to 75 °C)
- Low warping, no enclosure required
- Tough with good layer adhesion
- Resists water and humidity
- Bambu suggests PETG HF for outdoor items
Cons
- Prone to stringing
- Can bond too strongly to smooth PEI
- Weak bridging and overhangs
- Supports are hard to remove
- Needs drying before long prints
Frequently asked questions
Is PETG food safe?
Prusa says PETG in itself may be considered food-safe, but it does not recommend any filament for direct food contact because layer lines can harbor bacteria. Bambu's PETG HF page makes no food-contact claim. Check the specific product's documentation.
Does PETG need an enclosure?
No. PETG has low warping and prints well on open-frame printers such as the Bambu Lab A1. An enclosure does no harm, and enclosed printers like the P1S list PETG as an ideal material.
Why does PETG string so much?
PETG oozes more than PLA at its print temperature. Prusa suggests increasing retraction, lowering the nozzle temperature and using print cooling. Wet filament also makes stringing worse, so dry it first.
Can PETG be used outdoors?
Bambu says its PETG HF resists water, UV and temperature and suggests it for outdoor items like planters. Prusa says PETG suits most exterior use below 80 °C. For long sun exposure, ASA is the usual upgrade.
What bed temperature does PETG need?
Makers list 60 to 80 °C (Bambu), 70 to 80 °C (Polymaker) and 85 to 90 °C (Prusa). Use glue or a textured sheet, because PETG can stick too hard to smooth PEI.
Sources
- Prusa Knowledge Base: PETG
- Bambu Lab Store: PETG HF
- Bambu Lab: Bambu Filament Guide (PDF)
- Polymaker: PolyLite PETG Technical Data Sheet V5.2 (PDF)
- Polymaker: PolyLite ABS Technical Data Sheet V5.2 (PDF)
- Prusa Knowledge Base: ASA
- UL Research Institutes: Comprehensive Emissions Data from Material Extrusion 3D Printing Now Available (Dec 2023)