PETG

PETG-CF

PETG filled with chopped carbon fiber for stiffer, more dimensionally stable parts. Needs a hardened nozzle, and an enclosure is recommended.

What it is

PETG-CF is PETG with short chopped carbon fibers blended into the filament. The base polymer brings PETG's toughness and chemical resistance, and the fibers add stiffness and dimensional stability. eSUN's product page for its PETG-CF lists flexural strength up to 84% and flexural modulus up to 195% higher than standard PETG, a heat distortion temperature of 70 °C, and a matte, frosted finish. It also says the material keeps PETG's low moisture absorption and chemical resistance.

Prusa's knowledge base explains the tradeoff that comes with any fiber-filled filament: fibers improve dimensional stability and reduce warping, but usually lower impact resistance and layer to layer adhesion, and they are highly abrasive, so a hardened nozzle is necessary.

Do not confuse PETG-CF with PET-CF. Polymaker's Fiberon PET-CF17 is a carbon-filled PET, not PETG, and it prints far hotter at 270 to 300 °C with the cooling fan off.

Print settings in practice

Two filament makers publish ranges that overlap:

  • Nozzle: Bambu Lab lists 240 to 270 °C for its PETG-CF. eSUN lists 240 to 260 °C. About 250 °C sits inside both.
  • Bed: Bambu Lab lists 60 to 80 °C on smooth or textured PEI. eSUN lists 75 to 90 °C and says a heated bed is required. 80 °C falls inside both ranges.
  • Speed and cooling: Bambu Lab lists under 200 mm/s with the part fan at 0 to 40%. eSUN lists under 150 mm/s with the fan at 100%, so follow the profile for your brand.
  • Drying: Bambu Lab lists 65 °C for 8 hours in a blast drying oven on its product page, while its wiki material table lists 70 °C for 8 hours and marks drying as recommended. eSUN lists 65 °C for more than 8 hours.
  • Enclosure: Bambu Lab's table recommends an enclosed printer because low ambient temperatures weaken layer bonding in PETG-type materials. eSUN also recommends enclosed-chamber printing.
  • Annealing: Bambu Lab lists 65 to 70 °C for 6 to 12 hours.

Nozzle choice

Both Bambu Lab and eSUN call for a hardened steel nozzle. eSUN lists 0.4 or 0.6 mm. Bambu's general abrasive advice is to avoid 0.2 mm nozzles, prefer 0.6 mm and slow down. It also warns that some brands of fiber-filled filament are rough enough to damage AMS feed channels, and its table marks PETG-CF as not recommended for the AMS lite.

Getting clean first layers

Prusa's composites article adds a few habits that cut down on clogs with any fiber-filled filament. Start with a clean nozzle, and do a cold pull before the print. Make sure the first layer goes down perfectly, because a poor first layer raises the risk of clogging. Prusa lists a 0.4 mm nozzle and 0.2 mm layer height as the smallest optimal values, and notes that composites generally print slightly hotter than the same unfilled plastic. Bambu Lab's general advice for abrasive filament also suggests cleaning the nozzle at 280 °C with an Allen key and a needle before use, and again if it clogs mid-print.

Strengths and weaknesses for real projects

PETG-CF is a practical choice for functional parts that must stay flat and rigid: mounting plates, fixtures, tool holders, outdoor brackets and enclosures. eSUN describes its PETG-CF as suitable for outdoor use, and the PETG base handles moisture better than nylon.

The weak direction is across layers. eSUN's figures show tensile strength of 51.3 MPa in the XY direction against 32.91 MPa in Z, and flexural strength of 77.2 MPa in XY against 49.9 MPa in Z. Orient parts so the main load runs along the layers. Impact strength is modest, so parts that get dropped or hammered may be better in plain PETG.

How it compares

  • PETG: Unfilled PETG is tougher on impact and prints on any nozzle. PETG-CF trades some toughness for stiffness and shape stability.
  • PLA-CF: Easier, cooler printing (210 to 240 °C per Bambu Lab) and fine on an open-frame printer, but Polymaker lists a heat deflection temperature of only 54 °C at 0.45 MPa for its PLA-CF.
  • Nylon (PA): Carbon-filled nylon is the step up for heat and wear, but Bambu Lab marks drying and desiccant as required and lists a 100 to 120 °C bed.
  • ASA: If the part lives outdoors and does not need fiber stiffness, ASA is the usual alternative to compare.

Which printers on this site can print it

You need a hardened nozzle, and an enclosure is recommended. These printers on this site combine both:

  • Bambu Lab P2S: enclosed, hardened steel nozzle and gears, up to 300 °C.
  • Creality K1C: enclosed, hardened steel nozzle up to 300 °C.
  • Elegoo Centauri Carbon 2: enclosed, 350 °C hardened steel nozzle.
  • Creality K2 Plus: enclosed with active chamber heating and a hardened steel nozzle up to 350 °C.
  • Bambu Lab X2D: two hardened steel nozzles and a heated chamber, though Bambu marks PETG-CF as "print with caution" on the auxiliary nozzle.

Flashforge lists PETG-CF as supported on the open-frame Flashforge AD5X. The Bambu Lab A1 Combo's AMS Lite lists generic PETG-CF as unsupported. See all of our enclosed printer picks.

Safety and ventilation

PETG-CF prints at moderate temperatures. Several printers above list activated carbon or HEPA filters, which is worth checking if the printer shares a room with people. Sanding or cutting fiber-filled parts creates fine dust, so avoid breathing it. Check the safety data sheet for your brand.

Storage

Bambu Lab says to keep PETG-CF sealed with desiccant to prevent moisture absorption. Its material table marks desiccant during use as optional for PETG-CF, but drying is recommended, so dry a spool that has sat open before an important print.

Print settings

TypePETG
BrandVarious
Nozzle / print temp250 °C
Bed temp80 °C
PriceNot listed

Pros and cons

Pros

  • Much stiffer than plain PETG (eSUN lists flexural modulus up to 195% higher)
  • Fibers improve dimensional stability and reduce warping
  • Keeps PETG's low moisture absorption and chemical resistance
  • Heat distortion temperature of 70 °C (eSUN PETG-CF)
  • Can be annealed after printing

Cons

  • Requires a hardened steel nozzle
  • Enclosure recommended for layer strength
  • Weaker across layers than along them
  • Not recommended for Bambu's AMS lite
  • Should be dried before printing

Frequently asked questions

Does PETG-CF need a hardened nozzle?

Yes. Bambu Lab and eSUN both call for a hardened steel nozzle because carbon fiber is abrasive and wears standard nozzles. Bambu also advises against 0.2 mm nozzles for fiber-filled filament.

What temperature do you print PETG-CF at?

Bambu Lab lists 240 to 270 °C and eSUN lists 240 to 260 °C, so around 250 °C is a reasonable start. Bed temperatures are 60 to 80 °C (Bambu Lab) and 75 to 90 °C (eSUN).

Does PETG-CF need an enclosure?

It is recommended. Bambu Lab says PETG-type materials print better enclosed because low ambient temperatures weaken layer bonding, and eSUN also recommends enclosed-chamber printing.

Is PETG-CF stronger than PETG?

It is stiffer. eSUN lists flexural strength up to 84% and flexural modulus up to 195% higher than standard PETG. Prusa notes that fiber fillers usually lower impact resistance and layer adhesion, so it is not stronger in every direction.

Is PETG-CF the same as PET-CF?

No. PET-CF uses PET rather than PETG as the base. Polymaker's Fiberon PET-CF17 prints at 270 to 300 °C with the fan off and is annealed at much higher temperatures than PETG-CF.

Sources