PLA
PLA+
PLA+ is a brand-specific family of modified PLAs marketed as tougher than PLA. It prints like PLA at about 190 to 230 °C but has similar heat limits.
What it is
PLA+ (also sold as PLA Plus or PLA Pro) is not a single standardized material. It is a marketing name that filament brands use for modified PLA blends designed to be tougher than standard PLA. Each brand uses its own recipe, so two spools labeled PLA+ can behave differently.
What the makers claim:
- eSUN says its PLA+ "improves the toughness and layer adherence" compared with PLA.
- SUNLU says its PLA+ is "particularly drop-resistant" and claims impact strength 2 to 3 times higher than other PLA or PLA+ on the market.
- Overture says its PLA Plus brings upgrades in print stability, layer adhesion, surface finish and structural strength.
- Bambu Lab does not use the PLA+ name, but sells PLA Tough, which it says offers 20% greater toughness and strength than regular PLA.
These are manufacturer claims. Because there is no shared standard, the most useful thing you can do is read the data sheet for the exact spool you plan to buy.
Print settings in practice
Published windows for PLA+ overlap closely with PLA, with some brands asking for a slightly hotter nozzle, especially at higher speeds:
- eSUN PLA+: 190 to 230 °C nozzle, 45 to 60 °C bed, and eSUN marks a heated bed as needed.
- SUNLU PLA+: 205 to 215 °C at 50 to 100 mm/s, rising to 215 to 245 °C at 100 to 200 mm/s, with a 50 to 60 °C bed and glue.
- Overture PLA Plus: its FAQ recommends 200 to 220 °C and a 50 to 60 °C bed (the spec table on the same page lists 190 to 230 °C for the nozzle).
- Bambu PLA Tough: 190 to 230 °C nozzle and 35 to 45 °C bed.
The 215 °C nozzle and 60 °C bed in the settings table fall inside the eSUN, SUNLU and Overture recommendations. If you print fast, follow SUNLU's approach and raise the nozzle temperature with speed, since the hotend has less time to melt each millimeter of filament.
Like PLA, PLA+ does not need an enclosure, and standard brass or stainless nozzles are fine for unfilled grades. Use the same build surfaces you use for PLA; a textured or smooth PEI plate is the common choice on current printers.
Strengths and weaknesses for real projects
PLA+ makes sense for parts that are handled, dropped or clipped together: tool holders, brackets, enclosures for electronics, toys and props that see rough use. It keeps PLA's easy printing and low warping while the maker claims better impact behavior and layer bonding.
What it does not fix is heat. SUNLU lists a Vicat softening temperature of 54 °C and a heat deflection temperature of 56 ± 3 °C for its PLA+. eSUN lists a heat distortion temperature of 53 °C at 0.45 MPa. Bambu's PLA Tough data sheet gives a Vicat softening temperature of 58 °C. Those numbers sit right alongside standard PLA, so PLA+ parts can still sag in a hot car.
Be careful comparing toughness numbers across brands. eSUN publishes an Izod impact strength of 4.53 kJ/m² (XY), Bambu publishes ISO 179 impact values for PLA Tough, and SUNLU's own page lists two different impact figures (8 kJ/m² in the text and 10 ± 3 kJ/m² in its table). Different methods and specimens make direct comparisons unreliable.
How it compares
- PLA: cheaper and more predictable from brand to brand. Choose PLA+ when toughness matters more than the last bit of detail or price.
- PETG: the better step up if you need heat resistance as well as toughness. Polymaker's PolyLite PETG lists a heat deflection temperature of 74.8 °C at 1.8 MPa, well above any PLA+ figure above.
- ABS and ASA: for parts that must survive real heat or sun, at the cost of an enclosure and ventilation.
- PLA-CF: stiffer rather than tougher, and abrasive, so it needs a hardened nozzle.
Which printers on this site can print it
Any printer that handles PLA handles PLA+. The main thing to check is nozzle temperature if you plan to use SUNLU's high-speed range, which reaches 245 °C. Every FDM printer on this site with a published maximum nozzle temperature lists at least 260 °C. At the time of writing (October 2026), official store prices included:
- Creality Ender-3 V3 SE at $179, with a 260 °C maximum nozzle temperature.
- Bambu Lab A1 mini at $199.
- Elegoo Neptune 4 Pro at $239.
- Anycubic Kobra 4 Combo at $379, which adds a 4-color ACE 2 Pro unit for multicolor PLA.
- Bambu Lab P1S at $349, an enclosed option if you also want ABS and ASA later.
For more shortlists, see our best 3D printers under $300 and best 3D printers for beginners.
Safety and food contact
The same general advice as PLA applies. UL Research Institutes reports that material extrusion printing releases ultrafine particles and volatile organic compounds that vary with filament and conditions, so print in a ventilated room.
Do not assume PLA+ is food safe. eSUN's page says its PLA+ "is approved by FDA" without stating what that approval covers, and the SUNLU and Overture pages make no food-contact statement. Additives that make PLA+ tougher are exactly the part of the recipe that differs between brands, so check the specific maker's documentation for any food-contact use.
Storage
Store PLA+ like PLA: sealed, with desiccant. SUNLU recommends keeping printing and storage containers below 20% relative humidity and drying at 50 °C in a drying oven. Overture lists 50 °C for 7 hours on its spec table (its FAQ suggests 55 °C for 4 hours for spools left open in humid conditions), and Bambu lists 55 °C for 8 hours for PLA Tough.
Print settings
| Type | PLA |
|---|---|
| Brand | Various |
| Nozzle / print temp | 215 °C |
| Bed temp | 60 °C |
| Price | Not listed |
Pros and cons
Pros
- Makers claim better toughness and layer adhesion than PLA
- Prints on any PLA-capable printer
- Low warping, no enclosure needed
- High-speed grades available from some brands
- Standard nozzles are fine
Cons
- No standard definition, recipes vary by brand
- Heat resistance close to PLA (about 53 to 58 °C)
- Settings differ between brands
- Some grades need a hotter nozzle at speed
- Toughness figures are hard to compare
Frequently asked questions
Is PLA+ stronger than PLA?
Makers say so. eSUN says its PLA+ improves toughness and layer adherence, and Bambu claims its PLA Tough has 20% greater toughness and strength than regular PLA. Because PLA+ recipes differ by brand, check the data sheet for the spool you buy.
Is PLA+ more heat resistant than PLA?
Not meaningfully. SUNLU lists a Vicat softening temperature of 54 °C for its PLA+ and eSUN lists a heat distortion temperature of 53 °C, close to standard PLA. For heat, look at PETG, ABS or ASA instead.
What temperature should I print PLA+ at?
eSUN lists 190 to 230 °C and Overture recommends 200 to 220 °C. SUNLU suggests 205 to 215 °C at normal speeds and up to 245 °C for fast printing. Around 215 °C with a 60 °C bed is a reasonable starting point.
Does PLA+ need a heated bed?
eSUN marks a heated bed as needed for its PLA+ and lists 45 to 60 °C. SUNLU and Overture recommend 50 to 60 °C. Most FDM printers on this site have one, but Toybox's comparison table lists no heated bed for its Toybox printer.
Can I use my PLA settings for PLA+?
Often they are a good starting point, since the published ranges overlap. Some brands ask for a slightly hotter nozzle, especially at high speeds, so check the maker's recommendation and adjust from there.
Sources
- eSUN: PLA+ product page and specifications
- SUNLU: PLA+ (PLA Plus) filament product page
- Overture: PLA Plus filament product page
- Bambu Lab: PLA Tough Technical Data Sheet (PDF)
- Polymaker: PolyLite PETG Technical Data Sheet V5.2 (PDF)
- UL Research Institutes: Comprehensive Emissions Data from Material Extrusion 3D Printing Now Available (Dec 2023)