TPU
TPU
TPU is a flexible, rubber-like filament, often sold as 95A (Bambu, Polymaker), for grips, bumpers and seals. It prints at about 220 to 240 °C but needs slow speeds and dry storage.
What it is
TPU (thermoplastic polyurethane) is the most common flexible filament. It bends, stretches and springs back, which makes it the material to reach for when a part needs to grip, cushion, seal or absorb impact. Prusa's knowledge base lists its strengths as flexibility and tenacity, dimensional stability (low shrinkage), good layer adhesion and high mechanical and chemical resistance.
TPU is sold by Shore hardness. Prusa says TPU is usually about 60A to 90A, and that the softer the filament, the harder it is to print. Many popular spools, including Bambu Lab TPU 95A HF and Polymaker PolyFlex TPU95, are 95A, at the firmer end, which is the easiest place to start. Bambu lists elongation at break above 700% (X-Y) for its TPU 95A, and Polymaker lists 551.2% for PolyFlex TPU95.
Print settings in practice
Temperatures are moderate; speed and feeding are where TPU gets tricky.
- Bambu TPU 95A HF: 220 to 240 °C nozzle, 30 to 35 °C bed with glue, under 200 mm/s for the high-flow grade. Bambu's standard TPU 95A data sheet lists under 80 mm/s.
- Bambu filament guide (TPU 95A): 220 to 240 °C nozzle, 30 to 35 °C on its Cool Plate and 30 to 45 °C on its Engineering, High Temperature and Textured PEI plates.
- Polymaker PolyFlex TPU95: 210 to 230 °C nozzle, 25 to 60 °C bed, cooling fan on, 30 to 50 mm/s, retraction 3 to 6 mm.
- Prusa (flexible materials): 230 to 245 °C nozzle and 60 to 75 °C bed. Prusa says a typical flexible speed is about 20 mm/s, with 30 to 40 mm/s as the maximum.
The 230 °C nozzle in the settings table falls inside the Bambu, Polymaker and Prusa ranges, and the 40 °C bed sits inside Bambu's PEI range and Polymaker's range.
Speed and retraction: go slow unless your filament is a high-flow grade. Prusa suggests lowering retraction (or turning it off and raising it gradually) to reduce clogs and tangling, and loosening the extruder idler so the gears push the filament gently.
Bed surface: Prusa recommends glue stick or another separator on smooth or satin sheets, and warns that very soft flex can bond too strongly to PEI. Its textured powder-coated sheets generally need no separator.
Feeding systems: check before you buy. Bambu's TPU 95A HF page says it is not compatible with the AMS or AMS lite, while Bambu sells a separate "TPU for AMS" filament that it lists as AMS and AMS lite compatible. Anycubic's Kobra 4 Combo product page lists TPU 95A among supported filaments but states "TPU 95A is not compatible with the ACE 2 Pro." Prusa also notes that filament sensors may not work reliably with flexible filament.
Annealing: Bambu's data sheet does not recommend annealing TPU prints, because complex prints can deform.
Strengths and weaknesses for real projects
TPU suits phone and device bumpers, feet and pads, grips, gaskets and seals, drone and RC bumpers, and flexible hinges or straps. Its low shrinkage and layer adhesion make it surprisingly forgiving in shape, even if it is slow to print.
Prusa's list of drawbacks is honest: high print difficulty, low printing speed, very bad bridging and overhangs, difficult support removal, stringing and moisture absorption. Design around those limits with flat bases, gentle overhangs and minimal supports.
How it compares
- PLA and PETG: rigid materials. Use them for the hard shell and TPU for the soft parts. Bambu says the Bambu Lab X2D's auxiliary nozzle can combine PLA and TPU in one part.
- Softer TPU grades: below 95A, Prusa notes printing gets harder. Start with 95A and move softer once your settings are dialed in.
- Nylon (PA): tough and slightly flexible but not rubbery, and much harder to print.
Which printers on this site can print it
Many printers on this site list TPU, but feeding matters as much as temperature. At the time of writing (October 2026), official store prices included:
- Creality Ender-3 V3 SE at $179; Creality says its Sprite direct extruder works with flexible TPU.
- Bambu Lab A1 mini at $199, with an 80 °C bed; Bambu lists ABS, ASA, PC and PA as not recommended on it, so it suits PLA, PETG and TPU.
- Elegoo Neptune 4 Pro at $239, with a dual-gear direct drive extruder and TPU on Elegoo's materials list.
- Bambu Lab A1 at $259.
- Anycubic Kobra 4 Combo at $379; Anycubic lists TPU 95A as supported but not through the ACE 2 Pro.
- QIDI Q2 at $499, enclosed, with TPU on QIDI's materials list.
The Flashforge Adventurer 5M lists TPU only with its 0.6 mm nozzle. If you want TPU in multicolor prints, read the feeding notes above and our best multicolor 3D printers; for low-cost options, see our best budget 3D printers.
Safety and ventilation
TPU does not carry the fume warnings that Prusa attaches to ABS and ASA, but UL Research Institutes reports that material extrusion printing releases ultrafine particles and volatile organic compounds that vary with filament and conditions. Print in a ventilated room as a general habit.
Storage
Moisture is TPU's biggest everyday problem. Bambu calls its TPU 95A HF "highly sensitive to humidity" and recommends storage below 20% relative humidity and drying at 70 °C for 8 hours before use. Polymaker lists the same 70 °C for 8 hours, and Prusa notes flexible filaments are hygroscopic and should be kept dry. Printing straight from a dry box is the easiest way to avoid stringing and bubbles.
Print settings
| Type | TPU |
|---|---|
| Brand | Various |
| Nozzle / print temp | 230 °C |
| Bed temp | 40 °C |
| Price | Not listed |
Pros and cons
Pros
- Flexible and tough
- Very high elongation (over 500%)
- Good layer adhesion and low shrinkage
- High mechanical and chemical resistance
- Moderate print temperatures
Cons
- Slow print speeds for standard grades
- Absorbs moisture quickly
- Stringing and poor overhangs
- Bambu TPU 95A HF can't use AMS; TPU 95A can't use ACE 2 Pro
- Softer grades are harder to print
Frequently asked questions
Can I print TPU through the Bambu Lab AMS?
Bambu's TPU 95A HF page says "AMS & AMS lite NOT Compatible." It sells a separate TPU for AMS filament that it lists as AMS and AMS lite compatible. Incompatible TPU has to be fed from outside the AMS, such as from the external spool holder.
What does 95A mean on TPU?
It is the Shore A hardness. Prusa says TPU is usually about 60A to 90A, and softer filament is harder to print. 95A is at the firm end, which makes it the easiest starting point.
How fast should I print TPU?
Prusa suggests about 20 mm/s, with 30 to 40 mm/s as a maximum. Polymaker lists 30 to 50 mm/s for PolyFlex TPU95. High-flow grades such as Bambu TPU 95A HF are rated for faster speeds, up to 200 mm/s.
Does TPU need to be dried?
Usually, yes. Bambu calls TPU 95A HF highly sensitive to humidity and recommends drying at 70 °C for 8 hours and storage below 20% relative humidity. Polymaker lists the same drying settings.
Which printers can print TPU?
Many printers on this site list TPU, including the Bambu Lab A1 and A1 mini, Creality Ender-3 V3 SE, Elegoo Neptune 4 Pro and QIDI Q2. Check whether TPU can go through the multicolor unit before relying on it.
Sources
- Prusa Knowledge Base: Flexible materials
- Bambu Lab Store: TPU 95A HF
- Bambu Lab: TPU 95A Technical Data Sheet (PDF)
- Bambu Lab: Bambu Filament Guide (PDF)
- Polymaker: PolyFlex TPU95 Technical Data Sheet V5.4 (PDF)
- Bambu Lab Store: TPU for AMS
- UL Research Institutes: Comprehensive Emissions Data from Material Extrusion 3D Printing Now Available (Dec 2023)
- Anycubic Store: Kobra 4 Combo (supported filaments)