PLA
PLA-CF
PLA filled with chopped carbon fiber. It prints at PLA-like temperatures but needs a hardened steel nozzle because the fibers are abrasive.
What it is
PLA-CF is ordinary PLA with short, chopped carbon fibers mixed into the plastic. It is not a woven carbon fiber composite. The fibers change how the filament behaves in three useful ways and one costly way. Prusa's knowledge base says carbon, glass and kevlar fillers improve dimensional stability, make parts lighter and less prone to warping, and raise heat resistance and tensile yield strength compared with the same unfilled plastic. The same page warns that fillers usually lower impact resistance and layer to layer adhesion, and that the fibers are highly abrasive, so a hardened nozzle is necessary.
That abrasion point is the one that decides whether your current printer can run it. Brass and stainless steel nozzles wear quickly on carbon-filled filament, according to Bambu Lab's filament guide.
Print settings in practice
Published ranges from two filament makers overlap closely:
- Nozzle: Bambu Lab lists 210 to 240 °C for its PLA-CF. Polymaker's PolyLite PLA-CF data sheet gives a 190 to 230 °C range and prints its specimens at 230 °C. A starting point of about 220 °C sits inside both.
- Bed: Bambu Lab lists 45 to 65 °C on smooth PEI and 55 to 65 °C on textured PEI. Polymaker gives 25 to 60 °C on PC or textured PEI, and prints its specimens at 50 °C.
- Speed and cooling: Bambu Lab lists under 250 mm/s with the part cooling fan at 50 to 100%. Polymaker lists 50 to 300 mm/s with the fan on.
- Drying: Bambu Lab recommends 55 °C for 8 hours in a blast drying oven and storing the spool sealed with desiccant. Polymaker lists 55 °C for 6 hours.
- Enclosure: Bambu Lab's material table marks both open-frame and enclosed printers as acceptable for PLA-CF.
- Annealing: Bambu Lab lists 55 to 60 °C for 6 to 12 hours.
Nozzle choice
Bambu Lab's general advice for abrasive filaments is to avoid brass and stainless steel nozzles, never use a 0.2 mm nozzle because clogs become very likely, treat 0.6 mm as the first choice and 0.4 mm as the second, and with a 0.4 mm nozzle keep layer heights between 0.15 and 0.3 mm and speeds to about 100 mm/s. Bambu notes its own PLA-CF is an exception that it recommends at 0.4 mm. Prusa adds that a clean nozzle and a good first layer reduce clogging, and recommends a cold pull before printing.
Multicolor systems
Bambu Lab's material table marks its own PLA-CF as compatible with the AMS and AMS lite, but warns that some brands of PLA-CF/GF are hard and rough enough to damage the AMS feed channel. If you plan to feed PLA-CF through any automatic material system, check the filament maker's compatibility notes first.
Strengths and weaknesses for real projects
PLA-CF suits parts where shape holding matters more than toughness: brackets, jigs, camera mounts, drone frames and enclosures that should not warp on a large flat base. The fiber fill helps dimensional stability, and the material keeps PLA's easy printing temperatures.
It is a poor choice for anything that gets hot. Bambu Lab lists low heat resistance as a con, and Polymaker's data sheet gives a heat deflection temperature of 54 °C at 0.45 MPa and 50 °C at 1.8 MPa. That is in the same territory as plain PLA, so a dashboard mount in a parked car is still a risk. It is also a poor choice for parts that take sharp impacts or rely on layer bonding, since Prusa lists the composite as more brittle with worse layer adhesion.
How it compares
- PLA: Plain PLA prints on any nozzle. Choose PLA-CF only if you need the extra dimensional stability and accept the nozzle upgrade.
- PLA+: Aimed at toughness rather than stiffness. If your parts crack on impact, PLA+ fits better than PLA-CF.
- PETG-CF: Same fiber idea on a PETG base. It needs a hotter nozzle (240 to 270 °C per Bambu Lab) and Bambu recommends an enclosure, but eSUN lists a heat distortion temperature of 70 °C for its PETG-CF.
- Nylon (PA): Carbon-filled nylon is the step up for hot, loaded parts, but it needs drying, a much hotter bed and an enclosure.
Which printers on this site can print it
The deciding spec is a hardened nozzle. Several printers on this site ship with one:
- Bambu Lab P2S: hardened steel nozzle and extruder gear, up to 300 °C. The older Bambu Lab P1S uses a stainless nozzle, which is the main material difference covered in P2S vs P1S.
- Creality K1C: ships with a hardened steel nozzle up to 300 °C, and the "C" in the name points to its carbon fiber focus.
- Elegoo Centauri Carbon 2: 350 °C hardened steel nozzle, so carbon fiber PLA needs no hardware change.
- Anycubic Kobra 4 Combo: hardened steel nozzle as standard.
Flashforge also lists PLA-CF among supported materials for the open-frame Flashforge AD5X; printer data on this site does not confirm a hardened nozzle, so check the nozzle before running abrasive filament. Open-frame budget printers can work too after a nozzle swap. The Bambu Lab A1 ships with a stainless steel nozzle that must be replaced with hardened steel before abrasive filaments. For more options, see the best 3D printers under $500.
Safety and ventilation
PLA-CF prints at PLA-like temperatures. Sanding or cutting fiber-filled parts creates dust, so treat it like any composite dust and avoid breathing it. Follow the safety data sheet for the specific brand you buy.
Storage
Keep spools sealed with desiccant between prints, as Bambu Lab recommends after drying. Polymaker suggests storing PolyLite PLA-CF in a dry box and lists an equilibrium water absorption of 0.38% on its data sheet. If prints start showing stringing or rough surfaces, dry the spool at 55 °C before blaming the printer.
Print settings
| Type | PLA |
|---|---|
| Brand | Various |
| Nozzle / print temp | 220 °C |
| Bed temp | 60 °C |
| Price | Not listed |
Pros and cons
Pros
- Prints at PLA-like temperatures (210 to 240 °C per Bambu Lab)
- Fibers improve dimensional stability and reduce warping
- Works on open-frame or enclosed printers
- Can be annealed after printing
- Some brands are AMS compatible (Bambu PLA-CF)
Cons
- Requires a hardened steel nozzle
- Low heat resistance, like plain PLA
- More brittle with weaker layer adhesion than unfilled PLA
- Clogs easily in 0.2 mm nozzles
- Some brands can wear AMS feed channels
Frequently asked questions
Do you need a hardened nozzle for PLA-CF?
Yes. Prusa calls carbon fibers highly abrasive and says a hardened nozzle is necessary, and Bambu Lab's material table marks a hardened steel nozzle as required for PLA-CF. Brass and stainless nozzles wear quickly on it.
What temperature should I print PLA-CF at?
Bambu Lab lists 210 to 240 °C for its PLA-CF, and Polymaker lists 190 to 230 °C for PolyLite PLA-CF. Start around 220 °C and adjust for the brand you use.
Is PLA-CF stronger than PLA?
It depends on the type of strength. Prusa says fiber fillers raise tensile yield strength and dimensional stability but usually lower impact resistance and layer adhesion. Expect a part that holds its shape better but can be more brittle.
Does PLA-CF need an enclosure?
No. Bambu Lab's filament table marks both open-frame and enclosed printers as acceptable for PLA-CF. The bigger requirement is a hardened steel nozzle.
Is PLA-CF heat resistant?
Not much more than PLA. Polymaker lists a heat deflection temperature of 54 °C at 0.45 MPa for PolyLite PLA-CF, and Bambu Lab lists low heat resistance as a con of its PLA-CF.