resin
ABS-like resin
A photopolymer formulated for more toughness than standard resin. It is not ABS plastic and needs the same gloves, washing, curing and disposal care.
What it is
ABS-like resin is a photopolymer for MSLA resin printers that resin makers formulate to be tougher than their standard resin. It is not ABS. The name describes the target behavior, not the chemistry, and the part still comes from the same UV-cured liquid workflow.
Anycubic describes its ABS-Like Resin+ as a high-performance resin with a balance of rigidity and toughness, aimed at detailed models, prototypes and figures. Its user manual lists 81.3 Shore D hardness, 32 MPa tensile strength, 25% elongation, 45 J/m notched impact strength, 3.72 to 4.24% volume shrinkage and a heat deflection temperature of 60 to 65 °C at 0.45 MPa. Elegoo markets its ABS-Like Resin V3.0 for high strength, toughness, precision and low shrinkage, but its product page gives no figures.
Because brands report different properties under different conditions, compare ABS-like resins using each maker's technical data sheet, and compare them against that same maker's standard resin rather than across brands.
Print settings in practice
Like all resins, it has no nozzle or bed temperature, so the settings table is empty. Exposure depends on the printer, the resin, the color and the room.
- Temperature: Anycubic recommends printing at 25 to 30 °C. At 15 to 20 °C, it says to increase exposure by 30% and reduce platform lift speed by 30%.
- Exposure tuning: Anycubic's troubleshooting advice is to raise bottom exposure by 30% for adhesion problems, raise exposure by 20 to 30% for faults across whole sections, and cut normal exposure by 20 to 30% if surfaces are rough. Its per-printer values are marked for reference only.
- Mixing: Anycubic says to shake the resin before each print, and to stir, filter and return it to its bottle if it has sat in the vat for more than 3 days.
Washing and curing
Anycubic lists 95% or stronger ethanol or IPA, or another resin cleaner, and warns not to soak parts for more than 30 minutes because prolonged soaking can cause swelling and damage. Blow off leftover solvent, and repeat washing and drying for parts with cavities. Post-cure for about 3 to 5 minutes, longer for complex parts. Make sure the part is clean and fully dry first to avoid whitening, and shorten curing for clear or white parts, which yellow more easily.
Strengths and weaknesses for real projects
ABS-like resin suits miniatures and figures that get handled, snap-fit prototypes, and thin features such as swords, antennas and tabs that break in standard resin.
It does not change resin's limits on heat. Anycubic's 60 to 65 °C heat deflection figure means it is not a replacement for engineering filaments in hot environments. Anycubic's manual still calls for gloves, a mask, ventilation and careful waste handling.
How it compares
- Standard resin: Usually the cheaper default with the same workflow. Choose ABS-like when parts break during handling.
- Water-washable resin: Changes the wash step, not the toughness. You trade IPA for water and a different waste routine.
- ABS filament: Real ABS is a thermoplastic printed on an FDM printer, with its own settings and ventilation needs. Compare it if you need larger parts with more heat resistance than Anycubic's 60 to 65 °C figure.
- Nylon (PA): For functional parts that flex and wear, nylon filament is the usual FDM option, but it needs drying and an enclosure.
Which printers on this site can print it
Every resin printer on this site is an MSLA machine that cures 405 nm resin through an LCD or display mask, so the question is less about compatibility and more about size, resin temperature control and workflow:
- Elegoo Mars 5 and Elegoo Mars 5 Ultra: compact printers for small parts and miniatures. Elegoo sells bundles with its Mercury wash and cure stations.
- Elegoo Saturn 4 Ultra: a 10 in 12K printer for batches or larger parts, which also means more resin per vat fill. See Mars 5 Ultra vs Saturn 4 Ultra.
- Anycubic Photon Mono M7 Pro: Anycubic lists compatibility with standard, ABS-like, water-washable, high-speed and plant-based resins, and its vat heats resin to a set 20 to 40 °C, which helps in cold rooms.
- Formlabs Form 4: holds resin at 25 to 45 °C and runs Formlabs' own resins, with third-party resins through Open Material Mode.
For picks by budget, see the best resin 3D printers and the best printers for miniatures. If you are still deciding between resin and filament, read FDM vs resin.
Safety and ventilation
Toughness does not remove the handling precautions. Anycubic's ABS-Like Resin+ manual says to place the printer in a well-ventilated environment, to wear masks and gloves, and suggests an air purifier for more sensitive users. The manual does not list hazard statements; it says to contact Anycubic customer service for the MSDS. Hazard classifications differ between products, so get the SDS for the exact bottle you buy rather than relying on another resin's sheet.
Other makers give similar basic advice for their own products. Formlabs' safety guide for its SLA products says to wear nitrile or neoprene gloves to prevent skin contact with liquid resin and wash solvents, to wear safety glasses during post-processing, to wash exposed skin promptly with soap and water, and to run printers where air circulates freely rather than in a closet, ideally with at least three full air exchanges per hour. Elegoo's product safety page for ELEGOO Photopolymer Resin uses the signal word "Warning", lists skin irritation, allergic skin reaction, serious eye irritation and long-lasting aquatic toxicity, and says to wear protective gloves, eye protection and face protection, keep it out of reach of children and avoid release to the environment.
Waste disposal
Anycubic says never to pour cleaning solution into the sewer. Leave dirty solvent in a clear container in sunlight or UV until the dissolved resin solidifies, then filter it; the filtered solvent can be reused. Let spent IPA or ethanol evaporate, cure the remaining resin, and dispose of the solid under local rules; Anycubic says fully cured waste can be treated as regular plastic waste. Formlabs adds that liquid resin may be classified as hazardous waste in your region, that resin-soaked paper towels should be cured in sunlight or UV light before going in household waste, and that used solvent disposal rules vary by location.
Storage
Formlabs recommends storing resin between 10 and 25 °C, away from direct sunlight, and moving it from the vat into an opaque container for long-term storage. Anycubic lists a shelf life of 1.5 years for its ABS-Like Resin+.
Print settings
| Type | resin |
|---|---|
| Brand | Various |
| Nozzle / print temp | N/A (UV cured) |
| Bed temp | N/A |
| Price | Not listed |
Pros and cons
Pros
- Formulated to balance rigidity and toughness
- 25% elongation at break (Anycubic ABS-Like Resin+)
- Low volume shrinkage (3.72 to 4.24% for Anycubic)
- Washes in 95% IPA or ethanol like standard resin
- Anycubic rates it for 365 to 405 nm light-curing printers
Cons
- Needs gloves, a mask and ventilation (Anycubic)
- Heat deflection only 60 to 65 °C (Anycubic)
- Parts can swell if soaked over 30 minutes
- White and clear parts yellow with long curing
- Toughness claims vary widely between brands
Frequently asked questions
Is ABS-like resin the same as ABS?
No. ABS-like resin is a UV-cured photopolymer formulated to be tougher than standard resin. ABS is a thermoplastic filament printed on FDM printers, with different settings and safety needs.
Is ABS-like resin stronger than standard resin?
Makers formulate it for toughness. Anycubic describes its ABS-Like Resin+ as balancing rigidity and toughness and lists 25% elongation. Exact figures vary by brand, so compare each maker's data sheets.
How do you wash ABS-like resin prints?
Anycubic recommends 95% or stronger IPA or ethanol, or another resin cleaner, and warns against soaking for more than 30 minutes because parts can swell. Dry parts fully before curing to avoid whitening.
Why do my ABS-like resin prints turn yellow?
Anycubic notes that clear and white parts yellow more easily and recommends a shorter post-cure for them. It lists about 3 to 5 minutes of post-curing for its ABS-Like Resin+.
Does ABS-like resin need different exposure settings?
Use the profile for that resin and your printer as a starting point. Anycubic says to increase exposure by 30% when the room is 15 to 20 °C and recommends printing at 25 to 30 °C.