resin

Water-washable resin

Photopolymer resin whose uncured residue rinses off with water instead of IPA. It still needs gloves and curing, and the wash water cannot go down the drain.

What it is

Water-washable resin is a photopolymer for MSLA printers whose uncured residue can be rinsed off a print with water rather than isopropyl alcohol. Elegoo, Anycubic and Siraya Tech all sell versions. The main appeal is avoiding a stock of IPA, and Elegoo markets its version for hassle-free, odor-free cleanup.

What it does not change is the chemistry risk. The resin is still a light-curing liquid that should not touch skin, and the rinse water now carries dissolved or suspended resin, so it needs the same care as dirty IPA.

As an example of specs, Anycubic lists its Water-Wash Resin at 82 to 85 Shore D hardness, 38 to 43 MPa tensile strength, 16 to 22% elongation at break and 2.2 to 5.5% volume shrinkage.

Print settings in practice

Like all resins, it has no nozzle or bed temperature, so the settings table is empty. Exposure depends on the printer, resin and room temperature.

  • Exposure: Anycubic lists 25 to 40 s for bottom layers and 2 to 2.5 s for normal layers. Its Photon Mono M7 profile uses 2.5 s normal and 35 s bottom exposure at 0.05 mm layers.
  • Temperature: Anycubic's product page says to use the resin above 20 °C, and its Water-Wash Resin+ user guide gives 18 to 35 °C as the operating range, with preheating allowed but not above 60 °C.
  • Light: Print in a dim, ventilated area or keep the printer covered, since sunlight cures the resin.

Washing and curing

Anycubic lists at least 5 minutes in water, or at least 3 minutes in 95% IPA, and about 10 minutes in a Wash & Cure machine. Anycubic's user guide for its Water-Wash Resin+ says not to soak parts in water for more than 30 minutes because prolonged soaking can cause swelling and damage, and its product page says to take parts out promptly and dry them to prevent water absorption and cracking. Blow off remaining water, check for resin residue and repeat if needed. Anycubic lists about 3 minutes of UV curing, with 3 to 5 minutes for secondary curing.

Not every water-washable resin behaves the same in water. Siraya Tech says its Simple resin disperses and dissolves in water, while other water-washable resins it compared sank and clustered together. Siraya recommends a diluted alcohol mix for cleaning Simple (one part 90% alcohol to five parts water) and says a print can be cleaned in under 60 seconds.

Strengths and weaknesses for real projects

Water-washable resin suits people who print occasionally, share a space with others, or do not want to buy and store IPA. Swapping the solvent does not remove gloves, ventilation or curing from the routine.

The weakness is the wash water. You build up a container of resin-laden water that must be cured or evaporated before disposal. Parts also need prompt drying, because Anycubic warns that water left in parts can lead to cracking.

How it compares

  • Standard resin: Cleans with IPA. Choose standard resin if you already run an IPA wash station and want the widest choice of resins and profiles.
  • ABS-like resin: A toughness upgrade, not a washing change. Some makers sell tougher water-washable blends too, so check the data sheet.
  • PLA: If you want no liquid chemistry at all, an FDM printer avoids washing entirely.

Which printers on this site can print it

Every resin printer on this site is an MSLA machine that cures 405 nm resin through an LCD or display mask, so the question is less about compatibility and more about size, resin temperature control and workflow:

  • Elegoo Mars 5 and Elegoo Mars 5 Ultra: compact printers for small parts and miniatures. Elegoo sells bundles with its Mercury wash and cure stations.
  • Elegoo Saturn 4 Ultra: a 10 in 12K printer for batches or larger parts, which also means more resin per vat fill. See Mars 5 Ultra vs Saturn 4 Ultra.
  • Anycubic Photon Mono M7 Pro: Anycubic lists compatibility with standard, ABS-like, water-washable, high-speed and plant-based resins, and its vat heats resin to a set 20 to 40 °C, which helps in cold rooms.
  • Formlabs Form 4: holds resin at 25 to 45 °C and runs Formlabs' own resins, with third-party resins through Open Material Mode.

For picks by budget, see the best resin 3D printers and the best printers for miniatures. If you are still deciding between resin and filament, read FDM vs resin.

Safety and ventilation

"Water-washable" describes cleanup, not safety. Anycubic's product page says to wear nitrile gloves and goggles, to avoid skin and eye contact, and to keep the resin away from pregnant women, children and pets. The Water-Wash Resin+ user guide points to that product's MSDS for full safety information. Siraya Tech says 405 nm UV resins in general can cause skin sensitivity.

Other makers give similar basic advice for their own products. Formlabs' safety guide for its SLA products says to wear nitrile or neoprene gloves to prevent skin contact with liquid resin and wash solvents, to wear safety glasses during post-processing, to wash exposed skin promptly with soap and water, and to run printers where air circulates freely rather than in a closet, ideally with at least three full air exchanges per hour. Elegoo's product safety page for ELEGOO Photopolymer Resin uses the signal word "Warning", lists skin irritation, allergic skin reaction, serious eye irritation and long-lasting aquatic toxicity, and says to wear protective gloves, eye protection and face protection, keep it out of reach of children and avoid release to the environment.

Waste disposal

Do not pour wash water down the drain. Anycubic's product page says to let wastewater cure in sunlight and then dispose of it as solid plastic waste, and its user guide suggests heating the water to evaporate it. Siraya Tech says wastewater from its Simple resin can be evaporated with very few by-products. Formlabs' general rules still apply: liquid or partially cured resin should not go into drains or household waste, liquid resin may be classified as hazardous waste in your region, and resin-soaked paper towels should be cured in sunlight or UV light before going in the trash.

Storage

Anycubic's user guide says to store uncured resin in a cool, dark place at room temperature, protected from light and heat, and to stir or shake it if pigment settles. Formlabs recommends 10 to 25 °C storage and opaque containers for long-term storage outside the vat.

Print settings

Typeresin
BrandVarious
Nozzle / print tempN/A (UV cured)
Bed tempN/A
PriceNot listed

Pros and cons

Pros

  • Cleans with water instead of IPA
  • Similar exposure times to standard resin
  • Can also be washed in IPA if needed
  • Wash water can be cured or evaporated at home
  • Supported on common MSLA printers

Cons

  • Wash water contains resin and is not drain-safe
  • Still needs nitrile gloves and goggles (Anycubic)
  • Parts can absorb water and crack if left wet
  • Swelling if soaked for over 30 minutes
  • Not every brand dissolves fully in water

Frequently asked questions

Can you pour water-washable resin water down the drain?

No. Anycubic says not to pour wastewater down drains and to let it cure in sunlight before disposing of it as solid waste, or to evaporate it. Formlabs also says liquid resin should not go into drains.

Is water-washable resin safer than regular resin?

It removes the need for IPA, but the resin itself still needs care. Anycubic recommends nitrile gloves and goggles and says to keep it away from pregnant women, children and pets. Check the SDS for the exact product.

How long should I wash water-washable resin prints?

Anycubic lists at least 5 minutes in water and warns against soaking for more than 30 minutes, which can cause swelling. Dry parts promptly to avoid water absorption and cracking.

Do water-washable resin prints need curing?

Yes. Anycubic lists about 3 minutes of UV curing at 405 nm, with 3 to 5 minutes for secondary curing. Make sure the part is dry before curing.

Can I wash water-washable resin with IPA?

Anycubic lists 95% IPA for at least 3 minutes as an alternative wash for its Water-Wash Resin. Siraya Tech recommends a diluted alcohol mix for its Simple resin.

Sources