resin

Standard resin

General-purpose 405 nm photopolymer for MSLA printers. Prints fine detail but needs gloves, ventilation, an IPA wash, a UV post-cure and careful waste handling.

What it is

Standard resin is the default liquid photopolymer for consumer MSLA resin printers. The printer shines 405 nm UV light through a masked screen, and each exposed layer hardens. Unlike filament, the material arrives as a liquid that is hazardous until it is fully cured, so most of the real work is in handling, washing and curing rather than in printer settings.

Specs vary by brand. As one example, Anycubic lists its Standard Resin V2 at 80 to 83 Shore D hardness, 35 to 45 MPa tensile strength, 25 to 30% elongation at break and 4.3 to 5.6% volume shrinkage. Use such numbers to compare products from the same maker, since test conditions differ between brands.

Print settings in practice

Resin has no nozzle or bed temperature, which is why the settings table on this page is empty. What matters is exposure time, and that depends on the printer's light source, the resin, the color, layer height and room temperature.

  • Exposure: Anycubic lists 20 to 40 s for bottom layers and 2.5 to 3 s for normal layers on Standard Resin V2. Its Photon P1 profile uses 2 s normal and 20 s bottom exposure at 0.05 mm layers. Treat these as a starting point and use the resin maker's profile for your exact printer.
  • Temperature: Anycubic says to use the resin above 20 °C, noting that low temperatures reduce success rates and high temperatures speed up pigment settling. A heated vat or a warm room helps.
  • Light: Anycubic advises printing in a dim, ventilated area or covering the printer, because sunlight cures the resin.
  • Mixing: Anycubic says to shake the resin well before use. Formlabs says its resin pigments settle and to shake the cartridge and stir the resin in the tank before each print.

Washing and curing

Anycubic lists a wash in 95% IPA for 3 minutes or more, or about 10 minutes in a Wash & Cure machine, followed by a UV cure of about 3 minutes at 405 nm, with 3 to 5 minutes listed for secondary curing. A dedicated wash and cure station, or two IPA containers (dirty and clean) plus a UV lamp, is the usual setup.

Strengths and weaknesses for real projects

Standard resin suits display pieces, miniatures, jewelry masters, dental and product models, and small parts where surface detail matters more than impact strength. It is a poor fit for parts that flex, snap, or carry load, and every print adds a workflow: gloves on, wash, dry, cure, and a waste stream to manage. If parts break when handled, try ABS-like resin. If IPA is the problem, try water-washable resin, which still needs the same gloves and waste care.

How it compares

  • ABS-like resin: Formulated for more toughness. Anycubic describes its version as balancing rigidity and toughness. Same handling and post-processing.
  • Water-washable resin: Rinses off with water instead of IPA, but the wash water then contains resin and cannot go down the drain.
  • PLA: If you want functional parts without liquid chemicals, an FDM printer and PLA avoid the washing and curing steps entirely.

Which printers on this site can print it

Every resin printer on this site is an MSLA machine that cures 405 nm resin through an LCD or display mask, so the question is less about compatibility and more about size, resin temperature control and workflow:

  • Elegoo Mars 5 and Elegoo Mars 5 Ultra: compact printers for small parts and miniatures. Elegoo sells bundles with its Mercury wash and cure stations.
  • Elegoo Saturn 4 Ultra: a 10 in 12K printer for batches or larger parts, which also means more resin per vat fill. See Mars 5 Ultra vs Saturn 4 Ultra.
  • Anycubic Photon Mono M7 Pro: Anycubic lists compatibility with standard, ABS-like, water-washable, high-speed and plant-based resins, and its vat heats resin to a set 20 to 40 °C, which helps in cold rooms.
  • Formlabs Form 4: holds resin at 25 to 45 °C and runs Formlabs' own resins, with third-party resins through Open Material Mode.

For picks by budget, see the best resin 3D printers and the best printers for miniatures. If you are still deciding between resin and filament, read FDM vs resin.

Safety and ventilation

Read the safety data sheet (SDS) for the exact resin you buy. Anycubic's SDS for Standard Resin V2 carries the signal word "Danger" and lists H315 (causes skin irritation), H317 (may cause an allergic skin reaction), H318 (causes serious eye damage), H335 (may cause respiratory irritation) and H411 (toxic to aquatic life with long lasting effects). It calls for chemically resistant gloves, tightly fitting safety goggles, and a well-ventilated area, with a respirator fitted with an ABEK filter if ventilation is not enough. Phrozen's SDS for its Standard Series resin in Neon Lime lists butyl-rubber gloves and goggles and includes a "suspected of damaging the unborn child" hazard statement for that product.

Other makers give similar basic advice for their own products. Formlabs' safety guide for its SLA products says to wear nitrile or neoprene gloves to prevent skin contact with liquid resin and wash solvents, to wear safety glasses during post-processing, to wash exposed skin promptly with soap and water, and to run printers where air circulates freely rather than in a closet, ideally with at least three full air exchanges per hour. Elegoo's product safety page for ELEGOO Photopolymer Resin uses the signal word "Warning", lists skin irritation, allergic skin reaction, serious eye irritation and long-lasting aquatic toxicity, and says to wear protective gloves, eye protection and face protection, keep it out of reach of children and avoid release to the environment. Anycubic also says to keep its resin away from pregnant women, children and pets.

Waste disposal

Formlabs says never to pour liquid or partially cured resin into drains or household waste, and notes that liquid resin may be classified as hazardous waste in your region. Its suggested route without a chemical waste service is to pour small amounts into a labeled, clear container and cure them in sunlight (1 to 10 days) or under 405 nm light, then discard the solid. Paper towels and other items with resin on them can be cured in sunlight or UV light first. Used IPA with dissolved resin must not go down drains, and Formlabs says correct disposal of used solvent varies by location. Anycubic's product page says to let cleaning wastewater cure in sunlight and dispose of the solid as plastic waste, while its SDS says the liquid material and its container must be disposed of as hazardous waste. When guidance differs, follow the SDS and your local waste authority.

Storage

Formlabs recommends storing resin between 10 and 25 °C, away from direct sunlight, in a dry, cool, well-ventilated place, and moving resin out of the vat into an opaque container for long-term storage. Anycubic's SDS similarly says to keep it in a dry, cool, well-ventilated place out of direct sunlight.

Print settings

Typeresin
BrandVarious
Nozzle / print tempN/A (UV cured)
Bed tempN/A
PriceNot listed

Pros and cons

Pros

  • Short layer exposures (2.5 to 3 s for Anycubic Standard V2)
  • Washes clean in 95% IPA in a few minutes
  • Quick UV post-cure (3 to 5 minutes per Anycubic)
  • Fully cured scraps can go out as solid waste
  • Makers publish starting profiles for common printers

Cons

  • Anycubic V2 SDS: skin irritation, allergy and serious eye damage
  • Needs gloves, eye protection and ventilation
  • Anycubic V2 SDS: toxic to aquatic life (H411); keep it out of drains
  • Requires separate washing and curing steps
  • Works best above 20 °C

Frequently asked questions

Is 3D printing resin toxic?

Uncured resin carries hazard warnings on makers' safety data sheets, and they differ by product. Anycubic's SDS for Standard Resin V2 lists skin irritation, possible allergic skin reactions, serious eye damage, respiratory irritation and aquatic toxicity. Both Anycubic and Formlabs say fully cured resin can be discarded as solid or household waste.

Do I need gloves for resin printing?

Yes. Formlabs recommends nitrile or neoprene gloves for liquid resin and wash solvents, and Anycubic recommends nitrile gloves and goggles. Wash any exposed skin promptly with soap and water.

How long do you wash and cure standard resin prints?

Anycubic lists at least 3 minutes in 95% IPA (or about 10 minutes in a Wash & Cure machine) and a UV cure of about 3 minutes, with 3 to 5 minutes for secondary curing. Times vary by resin and part size, so check your resin's guide.

Can I pour resin or IPA down the drain?

No. Formlabs says not to pour liquid or partially cured resin into drains and not to pour used solvent with dissolved resin down drains. Cure small amounts of resin solid first and follow local rules for solvent.

What exposure time should I use for standard resin?

It depends on the printer and resin. Anycubic lists 2.5 to 3 s normal and 20 to 40 s bottom exposure for Standard Resin V2. Start from the resin maker's profile for your printer and adjust.

Sources